Polished concrete, epoxy flooring and floor preparation across Brisbane

How thick does a polished concrete floor need to be?

Summary

There is no single thickness that makes a concrete floor suitable for polishing. Mechanical polishing refines the surface of a suitable slab; it does not add a new concrete layer. A new slab or separate topping needs its own design. Confirm the proposed grinding, finished floor level and adjoining finishes before work begins.

A concrete sample has a smooth aggregate surface and an exposed grey edge showing stone within the slab.

By Dynamic Concrete Solutions • Published 5 November 2026

When planning a renovation, “How thick is polished concrete?” can mean three different things: the depth of the structural slab, the thickness of an added topping, or the amount removed during grinding. Treating those as the same measurement can leave you with the wrong allowance at doors, cabinets and adjoining floors.

Dynamic Concrete Solutions’ concrete polishing service assesses the slab and the intended finish. Start the conversation with the floor you have, the floor height you need and whether you are planning new concrete or working with an existing surface.

Polishing works on the concrete already there

Mechanical grinding removes material from the surface. Subsequent abrasive stages refine it to the agreed finish. The visible stone comes from aggregate within that concrete, rather than a decorative layer laid over it. Surface treatments may form part of the process, but they do not turn polishing into a new structural slab.

That is why a polished floor cannot be assigned a universal installation thickness in the way you might describe a tile. First establish whether the proposal is to finish the structural slab itself or to install and finish a separate topping.

The Australian Government’s Your Home guide to concrete slab floors distinguishes slab types, ground-and-polished finishes and toppings. These are different parts of a floor design, even when their finished surfaces look similar.

Two floor cross-sections show surface removal from a grey slab on the left and a dark added topping above a grey base on the right.
Refining a slab and adding a topping change the surface level in different ways.
  • Left: the dashed orange line marks the former surface. Grinding removes material to reach the lower, blue finished surface.
  • Right: a dark blue topping adds material above the grey base. The orange line marks the interface between them.

For a new slab, plan the polish before the pour

A new concrete floor has to satisfy its building design as well as the desired appearance. Its thickness, reinforcement and support are design matters. They depend on the project, including the loads and whether the slab is on the ground or suspended. A photograph of an attractive polished floor cannot establish those requirements.

Tell the builder and slab designer that the concrete will be exposed and mechanically finished. The concreter and polishing contractor can then coordinate the mix, placement, surface finish, curing, protection, joints and intended aggregate exposure with that design.

The American Concrete Institute’s polished concrete slab finish specification covers the finishing work on both ground-supported and suspended slabs. Its scope separates that work from construction of the concrete slab itself. A finish specification and a structural slab design answer different questions.

The relevant allowance is not just “extra concrete for polishing”. The planned surface removal must remain compatible with the specified concrete cover over reinforcement and any embedded services. The design team needs to resolve that before placement, rather than assuming a nominal slab thickness leaves an unlimited grinding allowance.

For an existing slab, thickness alone is not a pass

A slab can be substantial and still be unsuitable for the finish you want. Weak material, repairs, contamination, unevenness and previous grinding can affect the work. Conversely, removing tiles does not automatically mean an additional concrete layer is needed.

Gather drawings and available records of the original slab, renovations, previous grinding and any heating or services within it. Tell the contractor about suspended or post-tensioned construction. Where the information is missing, the assessment needs to establish what can safely be done; appearance alone cannot reveal concealed details.

Our guide to polishing old concrete explains the separate suitability checks. For the thickness question, the key point is to establish the permitted work on this slab before agreeing how much material will be removed.

A topping is a separate proposal

A topping adds material above the existing base. It might be considered when a different surface or floor level is needed, but it should be identified explicitly in the proposal. It is not simply another name for polishing the existing slab.

Ask what the proposed topping is, whether it is intended to be mechanically polished, how it will be supported or bonded, and what thickness its design requires. Preparation, moisture, movement and the condition of the base still matter. Adding a layer does not by itself resolve an underlying defect.

A levelling compound intended to sit beneath another floor covering should not be assumed to be a finished, polishable surface. Likewise, a thin decorative cement finish is a different system with its own requirements. Confirm the actual system before comparing thicknesses or accepting a floor-height allowance.

Agree finished floor levels at the awkward edges

Imagine replacing tiles in a hallway while retaining them in the kitchen. Removing the hallway tiles and adhesive reveals a lower starting surface. Polishing that concrete does not replace the height of the removed tile build-up. The join between the rooms therefore needs a measured transition detail.

Now consider the reverse: adding a topping raises the finished surface. That can affect door clearance, appliance removal, skirting, cabinetry and thresholds. A plan that fits the open room may still fail at a sliding-door track or the first stair.

Have the builder or relevant trades record the proposed finished floor level against a common reference point. Include adjoining finishes and the highest and lowest areas, rather than measuring one convenient corner. Settle these details before ordering joinery or changing doors.

More grinding changes more than height

Grinding further into a slab can reveal a different aggregate pattern. It is not a neutral way to chase a lower floor level. The depth needed to address a high area may also change its appearance compared with the rest of the room.

Choose aggregate exposure and sheen separately. A higher gloss does not mean the contractor needs to remove more structural concrete. A representative test area can help show the appearance, while the permitted grinding depth still needs to be established for the project.

What should the written proposal clarify?

Before accepting a polishing proposal, make sure it answers these practical questions:

  • Are we polishing the existing slab, a new slab or a separate topping?
  • Who confirms the slab design and any limits on surface removal?
  • What finished floor levels and transitions have been agreed?
  • How will aggregate exposure, edges, joints and existing repairs be treated?
  • What needs further investigation before the scope can be confirmed?

Keep the slab information, finish selection and level details together. That gives the builder, designer and floor contractor the same starting point and makes changes easier to resolve before they affect adjoining work.

Floor height and grinding questions

How much concrete will grinding remove?

There is no single removal depth for every floor. The slab condition, high spots and agreed aggregate exposure affect the proposed cut. Ask the polishing contractor to state the intended surface removal, and have any limits from the slab design or concealed services confirmed before work starts.

Will polishing bring the slab up to the height of my old tiles?

No. Polishing the existing slab removes material; it does not replace the height of tiles and adhesive taken away. Measure the proposed finished level against adjoining floors, doors and stairs. Any topping or transition is a separate part of the proposal.

Does a higher gloss need a deeper grind?

A higher gloss does not by itself require deeper aggregate exposure. Exposure describes how much stone is revealed; sheen describes the refined surface appearance. Specify both separately so that the proposed finish and surface removal are clear.

To discuss your floor, contact Dynamic Concrete Solutions about concrete polishing. Send your plans or photos, including the existing covering and any known floor-level constraints. Or call 0401 151 092.

Facebook
Twitter
LinkedIn
Call now0401 151 092